![]() NOTE: If you feel that the knob assembly could be a little tighter, simply remove the screws and Knob Cap, tighten the Delrin Knob Body to align with the previously shown hole orientation and replace the screws and cap. Place each of the 6 Cap Head Screws into the Knob Cap and tighten with the included Hex Key. Align the holes of the inner Stainless Steel Core to the holes of the Delrin Knob Body and set the Knob Cap into place. You’ll want the hole pattern on the top of the Delrin Knob Body to mirror the orientation of the image below.Ĩ. Place the Delrin Knob Body over the Stainless Steel Core piece and begin threading it onto the shift rod and tighten until snug. Insert the front tabs of the Shifter Trim Surround back onto the center console and then ensure all remaining tabs snap in and engage completely.ħ. Flip the assembly over and place the Stainless Steel Core piece onto the shifter shaft. Place the Stainless Steel Core piece up through the inverted shift boot and utilizing the included o-ring, capture the tabs of the shift boot within the groove of the Stainless Steel Core piece.Ħ. Peel the triangle ends of the boot off the plastic ring.ĥ. Flip the Shifter Trim Surround over and push the boot inside out so you can access the plastic ring glued to the end of the shift boot. If it has detached itself, simply snap the inner shift boot structure back into place on the underside of the trim surround.Ĥ. The shift boot should remain attached to the trim surround. Once you have the edges released, simply pivot off the front tabs and lift out. For the more involved installation, remove the Shifter Boot Trim Surround by loosening the left, right and rearward edges with a Body Panel Removal Tool (or flat-bladed screwdriver). You’ll want the hole pattern on the top of the Delrin Knob Body to mirror the orientation of the image below.Īlign the holes of the inner Stainless Steel Core to the holes of the Delrin Knob Body and set the Knob Cap into place. ![]() Take the Delrin Knob Body and thread it onto the shift rod and tighten until snug. Place the Stainless Steel Core piece over the shifter. If you’ve decided upon the simple install, complete the following steps. Remove the factory shift knob by unscrewing it in the normal fashion.Ģ. The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. The cookie is used to store the user consent for the cookies in the category "Performance". This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other. The cookies is used to store the user consent for the cookies in the category "Necessary". The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional". The cookie is used to store the user consent for the cookies in the category "Analytics". These cookies ensure basic functionalities and security features of the website, anonymously. Necessary cookies are absolutely essential for the website to function properly. Remove the factory shift knob by unscrewing it in the normal fashion. Order our Miata shift extender today and take your driving experience to the next level! ![]() Installation is easy and straightforward, so you can start enjoying the benefits of a more ergonomic and comfortable shifting experience in no time. The black powder coating matches well with the stock interior and gear knob, while the polished aluminum and red options add a stylish touch to your car’s interior. 4′′ effective lift and overall length of approximately 5′′Ĭrafted from high-quality Duralumin, our shift extender is built to last and is available in polished aluminum, red, or black powder coating.3′′ effective lift and overall length of approximately 4′′.2′′ effective lift and overall length of approximately 3′′.1′′ effective lift and overall length of approximately 2′′.With effective lifts ranging from 1 inch to 4 inches and overall lengths ranging from 2 inches to 5 inches, our shift extender is designed to fully integrate between the knob and the gaiter for a seamless look. Get the most out of your Mazda Miata MX5’s manual transmission with our Duralumin Miata shift extender.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |